The post Bolt Shroud De-Cocking Tool – Tikka appeared first on Delta Tactical.

Features:

• CNC machined 431 Stainless Steel Shaft
• 6061 Aluminum knob
• Cerakoted Graphite Black (shaft and knob)
• All screws included as well as allen keys required for fitment
• Made in Australia

The post Tikka T1X Titanium Grooved Bolt Handle Stainless Steel appeared first on Delta Tactical.

Following the success of our CZ455 and 457 scope bases, it only made sense for us to begin to roll out bases for Anschutz rifles.

This design, made from a single piece of T7075 aluminum and machined in house on our Haas VF4SS 4 axis machining center is designed to slide onto the dovetail and be clamped down with a force that is consistent across the entire rail – and strong enough that your rimfire will never budge it. Bases will come Type III black hardcoat anodized and will come with the necessary wrench for torquing the clamp screws.

Recommended torque spec: 22 in/lb (2.5 NM)

Our rail comes in a 30MOA cant as it is meant for guys pushing their 22LRs out to 300+ yards or using optics with a minimum of 60MOA internal elevation, zeroing at 50y. We added real estate to the front of the rail to allow you to move your optic forward. This helps on higher powered scopes when coupled with the smaller stocks that are normal on a rimfire. This base is a little taller than the popular set-screw models (our rail adds a total of about 1/2″ of height to the dovetail) but by using lower height rings/mounts you should be able to retain a similar over bore height and maintain a good cheek weld without any riser.

Since we are good guys, and the machine would already be working in the area, we decided to build in a level to the base.  The material is flared out in the area to provide optimum viewing when in the prone position without much movement if any.

The post Anschutz 1761 Scope Base, 15MOA appeared first on Delta Tactical.

This design, made from a single piece of T7075 aluminum and machined in house on our Haas VF4SS 4 axis machining center is designed to slide onto the dovetail and be clamped down with a force that is consistent across the entire rail – and strong enough that your Sako Quad will never budge it.  For added security we have added a recoil lug at the rear of the base, creating a mechanical stop for the base. Bases will come Type III black hardcoat anodized and will come with the necessary 3mm hex key for torquing the clamp screws.  Recommended torque spec: 22 in/lb (2.5 NM)

Our rail comes in a 30MOA cant as it is meant for guys pushing their rimfires out to 300+ yards. We also added real estate to the front of the rail to allow you to move your optic forward. This helps on higher powered scopes when coupled with the smaller stocks that are normal on a rimfire. This base is a little taller than the popular set-screw models (our rail adds a total of about 1/2″ of height to the dovetail) but by using lower height rings/mounts you should be able to retain a similar over bore height and maintain a good cheek weld without any riser.

Since we are good guys, and the machine would already be working in the area, we decided to build in a level to the base.  The material is flared out in the area to provide optimum viewing when in the prone position without much movement if any.

The post Sako Quad Scope Base – 30MOA appeared first on Delta Tactical.

This design, made from a single piece of T7075 aluminum and machined in house on our Haas VF4SS 4 axis machining center is designed to slide onto the dovetail and be clamped down with a force that is consistent across the entire rail – and strong enough that your CZ455 will never budge it. Bases will come Type III black hardcoat anodized and will come with the necessary wrench for torquing the clamp screws.

Recommended torque spec: 22 in/lb (2.5 NM)

Our rail comes in a 50MOA cant as it is meant for guys pushing their 22LRs out to 300+ yards. It will also be available in a 15MOA configuration. We added real estate to the front of the rail to allow you to move your optic forward. This helps on higher powered scopes when coupled with the smaller stocks that are normal on a rimfire. This base is a little taller than the popular set-screw models (our rail adds a total of about 1/2″ of height to the dovetail) but by using lower height rings/mounts you should be able to retain a similar over bore height and maintain a good cheek weld without any riser.

Since we are good guys, and the machine would already be working in the area, we decided to build in a level to the base.  The material is flared out in the area to provide optimum viewing when in the prone position without much movement if any.

The post CZ 457 Scope Base – 50MOA appeared first on Delta Tactical.

Rusan CZ527 – Picatinny rail Extended 140mm Length

Made in Europe

The post CZ527 – Picatinny rail Extended 140mm appeared first on Delta Tactical.

Made in Europe

The post CZ527 – Picatinny rail appeared first on Delta Tactical.

Features:

• CNC machined 431 Stainless Steel Shaft
• 6061 Aluminum knob
• Cerakoted Graphite Black (shaft and knob)
• All screws included as well as allen keys required for fitment
• Made in Australia

The post Tikka T1X Swept Ball Handle – Silver appeared first on Delta Tactical.

Following the success of our CZ455 and 457 scope bases, it only made sense for us to begin to roll out bases for Anschutz rifles.

This design, made from a single piece of T7075 aluminum and machined in house on our Haas VF4SS 4 axis machining center is designed to slide onto the dovetail and be clamped down with a force that is consistent across the entire rail – and strong enough that your rimfire will never budge it. Bases will come Type III black hardcoat anodized and will come with the necessary wrench for torquing the clamp screws.

Recommended torque spec: 22 in/lb (2.5 NM)

Our rail comes in a 30MOA cant as it is meant for guys pushing their 22LRs out to 300+ yards or using optics with a minimum of 60MOA internal elevation, zeroing at 50y. We added real estate to the front of the rail to allow you to move your optic forward. This helps on higher powered scopes when coupled with the smaller stocks that are normal on a rimfire. This base is a little taller than the popular set-screw models (our rail adds a total of about 1/2″ of height to the dovetail) but by using lower height rings/mounts you should be able to retain a similar over bore height and maintain a good cheek weld without any riser.

Since we are good guys, and the machine would already be working in the area, we decided to build in a level to the base.  The material is flared out in the area to provide optimum viewing when in the prone position without much movement if any.

The post Anschutz 1761 Scope Base, 30MOA appeared first on Delta Tactical.

Comes with stainless recoil pin to work with receivers that have the hole available, rail will still work on those that do not

As with our 700 rails, all screws are T10 Torx and the same length so no guessing which goes where

The MOA angle of the base is guaranteed to be true to the spec due to advanced fixturing

Machined to MIL-STD-1913

Type III Hardcoat Black anodized

Comes with a T10 Torx key

Screw Torque = 15in/lb

The post Tikka T1X Improved Scope Base – 30MOA appeared first on Delta Tactical.